b0069

ADAPTADOR 4 CAMARAS RASPBERRY

Referencia: B0069

Raspberry Pi multi camera adapter module is designed for connecting more than one camera to a single CSI camera port on Raspberry Pi board. One adapter board can connect 4 cameras and user can stack up maxim 4 adapter boards that means up to 16 cameras on a single Raspberry Pi board. Please note that Raspberry Pi multi camera adapter board is nascent product that may have some stability issues and limitations because of the cableâs signal integrity and RPiâs closed source video core libraries, so use it on your own risk.

Application

  • IoT cameras
  • Robot cameras
  • Wildlife cameras
  • 3D scanner

Features

  • Accommodate 4 Raspberry Pi cameras on an multi camera adapter board
  • Stackable and maxim cascade 4 adapter boards
  • 3 GPIOs required for multiplexing on one adapter board, 5 GPIOs for two adapter board, 9 GPIOs for four adapter board
  • All camera ports are FFC (flexible flat cable) connectors
  • DIP switches for easy stack up configuration
  • Support Raspberry Pi A/B/B+ and Pi 2.

Pin Configuration

DIP switches are used here for easy stack up configuration. When only one multi camera adapter board is used, the switches 1and 5 should be switched to ON position. If two multi camera adapter boards are used, the downside board should be switched 1 and 5 to ON and upside board should be switched 2 and 6 to ON position, and if 3 or 4 multi camera adapter boards are used together each board layer should be configured as the Table 1 shown.

Table 1 Pin Configuration

Operation

For proper operation, only one camera should be enabled at a time. In case of only one multi camera adapter board is used, driving Pin12 HIGH and driving Pin11 , Pin7 to LOW to enable camera A on the adapter board. Enable camera B, C and D, please refer the Table 2 for camera selection configuration. To disable all cameras on one adapter board, Enable 1 and Enable 2 signals should be toggled HIGH. Care should be taken that it is not allowed to drive the Enable 1 and Enable 2 LOW at the same time. When connecting more than two multi camera adapter boards, only one of the cameras can be enabled by enabling the desired camera on one adapter board, and disable all the cameras on the rest of adapter boards.

Table 2 Camera Selection Configuration

Camera Selection ConfigurationSelectionEnable 1Enable 2
A001
B101
C010
D110
No CameraX11
ErrorX00

(X: donât care)

 

49,99 €
60,49 €
(impuestos excl.)
(impuestos inc.)
Cantidad
Últimas unidades en stock

  Compra Segura

Todos los datos de compra son encriptados y protegidos

  Política de entrega

Envío en 48/72 horas

  Política de devolución

14 días de devolución

Raspberry Pi multi camera adapter module is designed for connecting more than one camera to a single CSI camera port on Raspberry Pi board. One adapter board can connect 4 cameras and user can stack up maxim 4 adapter boards that means up to 16 cameras on a single Raspberry Pi board. Please note that Raspberry Pi multi camera adapter board is nascent product that may have some stability issues and limitations because of the cableâs signal integrity and RPiâs closed source video core libraries, so use it on your own risk.

Application

  • IoT cameras
  • Robot cameras
  • Wildlife cameras
  • 3D scanner

Features

  • Accommodate 4 Raspberry Pi cameras on an multi camera adapter board
  • Stackable and maxim cascade 4 adapter boards
  • 3 GPIOs required for multiplexing on one adapter board, 5 GPIOs for two adapter board, 9 GPIOs for four adapter board
  • All camera ports are FFC (flexible flat cable) connectors
  • DIP switches for easy stack up configuration
  • Support Raspberry Pi A/B/B+ and Pi 2.

Pin Configuration

DIP switches are used here for easy stack up configuration. When only one multi camera adapter board is used, the switches 1and 5 should be switched to ON position. If two multi camera adapter boards are used, the downside board should be switched 1 and 5 to ON and upside board should be switched 2 and 6 to ON position, and if 3 or 4 multi camera adapter boards are used together each board layer should be configured as the Table 1 shown.

Table 1 Pin Configuration

Operation

For proper operation, only one camera should be enabled at a time. In case of only one multi camera adapter board is used, driving Pin12 HIGH and driving Pin11 , Pin7 to LOW to enable camera A on the adapter board. Enable camera B, C and D, please refer the Table 2 for camera selection configuration. To disable all cameras on one adapter board, Enable 1 and Enable 2 signals should be toggled HIGH. Care should be taken that it is not allowed to drive the Enable 1 and Enable 2 LOW at the same time. When connecting more than two multi camera adapter boards, only one of the cameras can be enabled by enabling the desired camera on one adapter board, and disable all the cameras on the rest of adapter boards.

Table 2 Camera Selection Configuration

Camera Selection ConfigurationSelectionEnable 1Enable 2
A001
B101
C010
D110
No CameraX11
ErrorX00

(X: donât care)

 

B0069
Nuevo

No hay ninguna opinión por el momento.